AmpFlow P40-250-P geborstelde elektromotor, 250 W, 12 V, 24 V of 36 VDC, 3400 tpm

Brand:AmpFlow

2.8/5

105.20

De AmpFlow P40-250-P is een pancake-achtige motor met hoog koppel, ontworpen om goede prestaties en efficiëntie te leveren tegen een voordelige prijs. Dit wordt bereikt door het gebruik van vier borstels en geavanceerde elektromagnetische computermodellering en ontwerp. De motor heeft een diameter van 4,0 inch en een lengte van 3,2 inch. De as is gelagerd in twee hoogwaardige kogellagers. De zware motorkabels zijn 14 inch lang. De motor weegt 4,2 pond en is afgewerkt met een hoogwaardige zwarte poedercoating. Deze omkeerbare motor kan worden gebruikt bij spanningen variërend van 12V tot 36Vdc. Bij 24 Volt is het onbelaste toerental 3400 RPM. Het nominale uitgangsvermogen is 250 W bij 2800 tpm bij 14 ampère. Het piekrendement is 78%. Deze motor wordt geleverd met een poelie met 13 tanden voor 5 mm HTD-riemAmpFlow®-motoren worden gebruikt in diverse toepassingen, waaronder robots, elektrische scooters, elektrische fietsen en andere persoonlijke transportsystemen. Zoek op Amazon naar AmpFlow-motoren voor meer keuzes.

Korte pannenkoekmotor met 13-tands poelie voor 5 mm HTD-riem. Piekrendement bij 24V: 78%. Continu vermogen: 250 watt (1/3 pk). Onbelast toerental: 3400 bij 24 volt; Kan worden gebruikt met spanningen variërend van 12V tot 36VDC. Meet 4,0 inch diameter (102 mm) bij 3,2 inch lang (81 mm).
Country of Origin USA
Item model number P40-250-P
Manufacturer Powerhouse Engineering Inc.
Package Dimensions 5.6 x 5.4 x 5.3 inches; 4.2 Pounds

2.8

8 Review
5 Star
32
4 Star
42
3 Star
9
2 Star
0
1 Star
17

Schrijf je beoordeling

Uw e-mail wordt niet gepubliceerd. Alle verplichte velden zijn gemarkeerd met*

Scritto da: john angelosanto
is a ok motor
for generate dc power
Scritto da: A. W.
Probably ok if you need the pulley that comes with it.
I bought this motor with the intention of removing the pulley, as the seller stated was possible in one of the answered questions. Since the motor has a D shaft and a circlip, I assumed the pulley wouldn't be pressed on (or if it was, it wouldn't truly be an interference fit). I was wrong. On top of that, the pulley seems to be made of cheese grade sintered metal, which broke when I hit it with a hard rubber mallet (part of the flange broke off). I attempted to heat the pulley with a torch to remove it, but I'm afraid because the shaft is so small/short, I'll get the rest of the motor too hot and damage it. The motor is much noisier than I expected too, though I didn't run it until after I attempted to remove the pulley, so I can't be sure if that's because I damaged the bearings. All in all, $59 + tax wasted.
Scritto da: MRB1953
Good little motor
Good little motor. Operates smooth. Appears to be well made. Would be nice to have had some better documentation for it.
Scritto da: paul
Does the job
I am using it for a Ians BFF Shaker in a flight simulator so far so good. See how long it lasts
Scritto da: Michael Pare
Misleading Photo
I should have heeded the warning from another review that showed the one-sided pulley. AND in addition to that flaw it was also cracked upon arrival! I can't imagine what use-case a one-sided pulley would serve. For double the price of the motor without the pulley, this is bad. It cost me time and extra parts to get this going.
Scritto da: Enrique I
My pulley doesn't have one end.
The motor is ok, but the reason I put 3 stars is that the pulley in the ilustration and the pulley of the motor I received, are not the same. My pulley doesn't have one end. I attach some photos, so you can check the two pulleys are slightly different. Regards.
Scritto da: Donald Rogers
This is the best motor for the job.
I didn't dislike any part of it.
Scritto da: James Klingbile
works
Prompt delivery, item was as advertised

Gerelateerde producten

Ontdek ons ​​internationale netwerk

We verzenden naar 28 landen, meer dan 200.000 producten. Blijf op de hoogte, schrijf je in voor de nieuwsbrief.

Array