0
0

Totaal:€ 0.00

Zie winkelwagenUitchecken
LoginRegister
0

Totaal:€ 0.00

Zie winkelwagenUitchecken
LoginRegister

PC Products PC-7 Epoxy-lijmpasta, tweedelig zwaar gebruik, 8 lb in twee blikken, antracietgrijs 128770

Brand:PC Products

3.7/5

€
179.93

PRODUCTBESCHRIJVING PC-7 is epoxy voor het zware werk. Deze pasta-epoxy is geformuleerd voor maximale hechtkracht. Wanneer ze worden gemengd, reageren de componenten A (grijs) en B (zwart) tot een binding van enorme sterkte. PC-7-formulering zorgt voor langere werktijd, voor grote en kritieke taken, waardoor de gebruiker het werk kan verplaatsen of wijzigingen kan aanbrengen. Hoge natte hechting van PC-7 Paste Epoxy maakt het werken boven en op de zijwanden gemakkelijk zonder druppelen of doorzakken. PC-7 vertoont uitstekende chemische weerstand tegen milde zuren, bijtende stoffen, detergenten, benzine, stookolie, zout en zoet water. Ongeveer gelijke hoeveelheden A en B per volume; variaties van beide componenten tot 20 procent hebben geen invloed op de hechtsterkte. Indien gewenst kunnen één deel van A tot twee delen B worden gebruikt om de elasticiteit te vergroten (dilatatievoegen, enz.). Plaats bij koude of koude temperaturen de PC-7-container vóór gebruik in de buurt van warmte. PC-7 mengt en verspreidt gemakkelijker bij 80 graden F dan bij 40 graden F. Elk schoon, glad, plat oppervlak is een uitstekend oppervlak om te mengen en te werken. Een klein plamuurmes of flexibele kunstenaarsspatel zijn geweldige hulpmiddelen voor het mengen en aanbrengen van PC-7. Gebruik als lijm: hout, metaal (alle soorten), glas, baksteen, blok, rubber, beton, steen, leisteen, glasvezel, tegels en meer in alle mogelijke combinaties; als afdichtmiddel: olie-, gas-, watertanks, kelderscheuren, druktanks en lekken in leidingen; als vulmiddel: gaten, gietstukken, patronen, mallen, holtes, lassen, stuurwielen en nog veel meer. Werktijd (70 graden F): 60 minuten. Kleefvrije uithardingstijd: 160 minuten. Kuur voor service: 24 uur. Maximale kuur: 7 dagen. Gardner slagvastheid: 160 in./Lb. Geleiding (elektrisch): niet geleidend. Uitstekende thermische schok. Niet giftig eenmaal uitgehard. Warmtebereik: -20 tot 200 graden F. VAN DE FABRIKANT PC-Products viert 75 jaar 'Fixing Your Things' met hoogwaardige, betrouwbare reparatieproducten. Reparatieoplossingen voor vrijwel alles wat gerepareerd moet worden of wat u kapot kunt maken. Van beton tot houtrestauratie en zware permanente reparaties, wij staan ​​voor u klaar. Ja; We kunnen dat oplossen

Hoeveelheid
Voeg toe aan winkelkarKoop nu

EAN: 0549831287704

Categorieën Industrieel & Wetenschappelijk, Adhesives, Sealants & Lubricants, Epoxies, Tile Epoxy Lijmen,

Het toepassingstemperatuurbereik is 35 tot 115 graden F en het servicetemperatuurbereik is -20 tot +200 graden F. Vult gaten, gietstukken en vormen. Dicht lekken van olie-, gas- en watertanks af, evenals scheuren in leidingen en metselwerk. Hecht veel materialen, waaronder glasvezel, hout, beton, veel metalen, baksteen, glas, keramiek en rubber. Tweecomponenten multifunctionele epoxylijmpasta werkt als hechtmiddel, afdichtmiddel en vulmiddel voor een reeks binnen- en buitentoepassingen.
Brand PC Products
Color Charcoal Gray
Compatible Material Fiberglass, Brick, Glass, Ceramic, Concrete
Country of Origin USA
Domestic Shipping Item can be shipped within U.S.
International Shipping This item can be shipped to select countries outside of the U.S.
Item Form Paste
Item model number 128770
Manufacturer Protective Coating Co.
Material Paste
Product Dimensions 13 x 6 x 6 inches; 8.49 Pounds

3.7

13 Review
5 Star
76
4 Star
15
3 Star
5
2 Star
1
1 Star
3

Schrijf je beoordeling

Uw e-mail wordt niet gepubliceerd. Alle verplichte velden zijn gemarkeerd met*

Scritto da: william
Works
I tried 3 different products and nothing held. This product worked great. For those who said it didn't set up I can only say mine set within 3 hours. Over night it was a solid "weld". I suggest your not useing equal parts. For small batches I used a food scale covered in plastic wrap and weighed out equal parts. I mixed it in an old glass pie plate for easy clean up and mixing. Throw away after use.
Scritto da: charles parham
Been around for decades and always works great.
This stuff has been around for decades. Anyone old enough can remember seeing their display in a hardware store where they glued multiple items to a soda bottle. If you follow the directions the product will work as advertised. It has the consistency of thick peanut putter and will hold its shape after you mix it. It will not run like ordinary epoxy. Note, because it is so thick it will be difficult to mix in cold weather. It is best to warm it up for a few hours before you mix it.
Scritto da: VIPERICHNAPLES
Really good
Liked everything. 24 hour cure, really rood adhesion, recommended. BTW before I bought this from Amazon, I tries a big box home improvement store. They said they never heard of a 2 part paste epoxy....I like that Amazon always has what I need for projects that come up.
Scritto da: Another Grandparent
Would definitely buy again for an epoxy/adhesive need
The descriptions, reviews, and videos seemed to indicate the 5 things we wanted/needed and I will review each part: 1) quickly setting - absolutely, very happy with this 2) great adhesion - again, so far so great (will update if this changes) 3) not like super glue in which it immediately sticks or you can't see it and causes a mess 4) thick that would not run - almost a homerun (pardon the pun), it did try to flow downward due to gravity which I gave a 1/2 a ding for: you'll need to help it not move for several minutes 5) easy to work with and mix - decent to work but still rather thick and we had to use the entire containers for the amount needed which made it harder and longer to have to stir that amount and yet quickly to prevent setting. FYI you either have several things to throw away or spend a lot of time cleaning up - a mixing area, a mixing tool, and gloves which caused another 1/2 ding We had an interesting large project to do requiring the entire amount of one set which meant a lot of material to mix at once and it's very stiff so it looks easy or sounds easy and probably is in smaller amounts. Our project required a tubular area (PVC pipe) to be filled and then adhere to a smaller, non-round post area and this would be placed vertically on top of the post. We cut out cardboard to be a plug at the bottom and used fasteners to try to hold them up and contain the material. The mix was heavy enough and loose enough and slow enough to press down and move the cardboard a little overnight. However, we are VERY pleased with the results because it actually stuck so hard to the cardboard that it was difficult to pull off, the tubes are holding great, and we started using the project right away the next day. Remember, this PVC pipe has to be "attached" to a smaller, irregularly shaped post. Bottomline, it held as we needed, it dried as quickly as we needed, and was stiff enough to want to stay and not run. As the subject says, if needed again we won't hesitate to buy it. Just a couple of small things to watch out for, still a great product months later. Btw they have some of the most flexible options to buy the amount of material without breaking the bank. :-)
Scritto da: Mauricio Mancinas
El producto cuplé con el trabajo
El producto cuplé con el trabajo, Sostiene desde el primer momento de aplicar, tarda un poco en secado 100% pero cuando lo hace es como una roca, definitivamente lo recomiendo, asegúrese de mezclar partes iguales y por un poco más de tiempo recomendado en la etiqueta así secará perfectamente y en menor tiempo.
Scritto da: Dennis s.
Works good
Strong bond
Scritto da: Amazon Customer
Good stuff
Very thick! But not unmanageable. It says it works on some plastics. I used it to fill in low spots and holes on a plastic composite intake manifold. Adhered perfectly. I believe it can be used as a filler.
Scritto da: alfred lipp
Impervious to gasoline
I had a lawnmower with 2 9 inch holes in the deck. Used the epoxy and a metal screen to fix holes. Great buy!
Scritto da: Mr Thomas R D Law
None drip epoxy paste works really well
Used this paste months ago bedding some steel into wood. The paste adhered to the wood perfectly, it holds the steel in place securely. It has not shrunk and confidence is high that it will provide a permanent fix. Also a lot cheaper than some more well known equivalents.
Scritto da: Michelle R
Epoxy
This is very good for outdoor repairs on a log cabin. Bit pricey for the amount you get, also quite messy.
Scritto da: Zoltan
Two-pack Filler
Works as advertised, it is a bit soft when set.
Scritto da: gordon p.
Useless
Doesn’t work followed instructions left for a day touched it and part fell off useless
Scritto da: Colour of the Gods
I hope you're a bodybuilder
I needed 2 part epoxy to fix a crack in my concrete floor in an outbuilding. Jump on Amazon, find this, "Great!" I think to myself. Some of the reviews say that the consistency is a little bit thick, but that should be alright. So, just for context I'm a regular weightlifter (people who've used this will know where I'm going here), and am not a strongman or anything, but live/work on a farm and try and stay reasonable strong. Well I hope that you're prepared for a journey that ends with four C's (THICCCC) as this stuff honestly is the most difficult epoxy I've ever worked with. The consistency is almost unbelievable. I broke my trowel mixing and applying this, and worked up a massive sweat. It completely ruined the containers I mixed it in (not a big deal) and left behind lots of sticky/thicccc residue that I couldn't scrape up and use properly. I'm sure that this is strong as Atlas himself (still waiting for curing/drying), but if I'm destroying tools just trying to mix it then it's really not fit for purpose (for me). Maybe I got a bad batch? I'm not sure. But the batch I got really is unworkable I'm afraid.

Gerelateerde producten

hot
MG Chemicals 9200FR Vlamvertragende structurele epoxylijm, 45 milliliter dubbele pneumatische dispenser 45 ml dubbele cartridge
3.9/5

€ 59.23

MG Chemicals 9200FR Vlamvertragende structurele epoxylijm, 45 milliliter dubbele pneumatische dispenser 45 ml dubbele cartridge
3.9/5

€ 59.23

hot
PC Products PC-Marine Epoxy Putty, 2oz Stick, Wit (25567) 2 oz
3.5/5

€ 28.95

PC Products PC-Marine Epoxy Putty, 2oz Stick, Wit (25567) 2 oz
3.5/5

€ 28.95

hot
3M Scotch-Weld epoxylijm DP125, doorschijnend, tweecomponenten epoxy, flexibele lijm, geluidstrillingshardheid, 48,5 ml (1,64 fl oz) Duo-Pak, 12/doos
2.9/5

€ 71.45

3M Scotch-Weld epoxylijm DP125, doorschijnend, tweecomponenten epoxy, flexibele lijm, geluidstrillingshardheid, 48,5 ml (1,64 fl oz) Duo-Pak, 12/doos
2.9/5

€ 71.45

hot
PC Products PC-Pool Epoxy Putty, vormbaar 4 oz Stick, gebroken wit 41116 gebroken wit
3.3/5

€ 27.48

PC Products PC-Pool Epoxy Putty, vormbaar 4 oz Stick, gebroken wit 41116 gebroken wit
3.3/5

€ 27.48

hot
West System 105-B epoxyhars
3.7/5

€ 183.83

West System 105-B epoxyhars
3.7/5

€ 183.83

hot
3M Scotch-Weld epoxylijm 1838, groen, deel B/A, 1 kwart kit
0.1/5

€ 519.13

3M Scotch-Weld epoxylijm 1838, groen, deel B/A, 1 kwart kit
0.1/5

€ 519.13

hot
PC Products PC-11 Epoxy-kleefpasta, tweedelige marinekwaliteit, 10 gal in twee emmers, gebroken wit 900116 PC-11 10 gallon
3.6/5

€ 1807.12

PC Products PC-11 Epoxy-kleefpasta, tweedelige marinekwaliteit, 10 gal in twee emmers, gebroken wit 900116 PC-11 10 gallon
3.6/5

€ 1807.12

hot
PC Products PC-7 Epoxy-lijmpasta, tweedelig zwaar gebruik, 4 lb in twee blikken, antracietgrijs 647776 4 lb in twee blikken 1
3.6/5

€ 108.06

PC Products PC-7 Epoxy-lijmpasta, tweedelig zwaar gebruik, 4 lb in twee blikken, antracietgrijs 647776 4 lb in twee blikken 1
3.6/5

€ 108.06

Ontdek ons ​​internationale netwerk

We verzenden naar 28 landen, meer dan 200.000 producten. Blijf op de hoogte, schrijf je in voor de nieuwsbrief.

Array

Totaal:€ 0.00

Zie winkelwagenUitchecken

Categorieën

Alle categorieën
Menu Categorieën In de buurt van Winkelwagen

Menu