Penn F93-serie luchtvolumeregeling voor diepe putten, opent bij drukval, geen meetkraan, geen drukontlastingsventiel F93A-1C

Brand:Johnson Controls

3.7/5

127.27

De F93-serie luchtvolumeregelaars voor diepe putten regelen de hoeveelheid lucht in de wateropslagtanks van diepe putwatersystemen. Diepe putten zijn meer dan 7,6 m diep. Regelingen uit de F93-serie houden automatisch het luchtvolume in de opslagtanks van diepe bronwatersystemen in stand door lucht uit de tank naar de omringende kamer te laten ontsnappen wanneer het waterniveau in de tank daalt (toename van het luchtvolume). F93 deepwell-bedieningselementen openen de luchtklep bij een daling van het tankwaterpeil en laten overtollige lucht uit de tank ontsnappen bij drukken tot 100 psig (690 kPa). De F93H heeft een minimale drukontlastingsklep om te voorkomen dat de tankdruk daalt tot onder 25 psig (172 kPa). Gebruik dit model bij toepassingen waar water snel kan worden afgevoerd. Raadpleeg het productbulletin F93 Series Air Volume Controls for Deep Wells (onderdeelnr. 24-7664-3000) voor belangrijke informatie over producttoepassingen.

stevige Noryl (high performance thermoplastic) behuizing is bestand tegen mechanische schade en corrosie.
Country of Origin USA
Item model number F93A-1C
Manufacturer Johnson Controls, Inc
Package Dimensions 10.2 x 3.94 x 1.73 inches; 7.05 Ounces

3.7

8 Review
5 Star
79
4 Star
12
3 Star
4
2 Star
2
1 Star
3

Schrijf je beoordeling

Uw e-mail wordt niet gepubliceerd. Alle verplichte velden zijn gemarkeerd met*

Scritto da: JS
Water tank switch
Fit great no issues
Scritto da: Beaty Wade Tharp
Fine valve
This style of valve is just fine for its function. My only wish is some ingenious engineer would figure out a way for the air vent portion of the valve to not get plugged up. I.e. some sort of wiper assembly that cleans off the air vent port as the float cycles up/down.
Scritto da: JERED ECKLE
Works like a champ!
Replaced one just like it in style. Immediately started working like it should after a few drain & fills of the tank!
Scritto da: MnBoy
It works.
Turned power off to deep well. Drained the water from the existing metal water tank through faucets. Waited until all the water... then air... left the tank. Closed the faucets. Took the old volume control out and put the new one in. This was a fairly easy procedure. Turned power on and waited for tank to fill. I could hear the air escaping the valve, which I did not hear on the old valve. The tank filled properly and I turned the faucets on to bleed air from lines. Pump runs only a fraction of what it did prior to new valve installation. I think the price is a bit high, but if it helps the pump by running less it is probably worth it.
Scritto da: Patrick
Identical to original.
Works fine but the arms on these floats are not a solid rod and that is what went bad on my old one. The arm bend up . These look identical to my original so i decided to beef up the rod with a piece of 8 awg solid copper wire soldered to the float arm. If not for the weak float arm this device would probably never fail.
Scritto da: Quail Valley Farm
Can't go wrong with Johnson Controls components
This switch closes the air pressure relief valve when the water level in the tank reaches the appropriate level. The switch was failing and dripping water in the pump house, non-stop. This is the exact same brand/model I replaced, and the one that failed was on the tank when I purchased the property in 2003, demonstrating its longevity. Given this is a farm tank, serving a home with a pool, and the property, it gets a significant workout. I suspect that because the well is inside of a structure, this switch and other components last somewhat longer than they would if the well system was exposed to the elements.
Scritto da: Mark Williamson
Says Penn, not Johnson controls.
Using it as a spare, not installed yet.
Scritto da: Roark
Works very well and has “secret” ability. :)
Perfect replacement for my deep-well system. Something not mentioned in the description is this has an *optional* outlet for gauge/pressure switch that is pre-threaded. If you dont need this feature, simply do nothing. This threaded recess does NOT by default connect to the tank-side pressure. If you want this feature, simply drill a small (tiny is fine!) hole in the threaded recess and screw your gauge or pressure switch in. That little hole connects the gauge to the pressure side of things. This means one unit can fill the role of two. Simply drill the hole to allow connection of a pressure switch or gauge. Neat!

Gerelateerde producten

hot
Emerson 760-401 vlamsensor
3.4/5

€ 56.43

Emerson 760-401 vlamsensor
3.4/5

€ 56.43

hot
Emerson 24A34-15 Warmtepompregeling
2.2/5

€ 42.84

Emerson 24A34-15 Warmtepompregeling
2.2/5

€ 42.84

Ontdek ons ​​internationale netwerk

We verzenden naar 28 landen, meer dan 200.000 producten. Blijf op de hoogte, schrijf je in voor de nieuwsbrief.

Array