Seachoice messing afvoerbuis, 6 inch lang, 1 inch ID, 90 graden flens aan één uiteinde

Brand:SEACHOICE

3.6/5

36.66

Seachoice Drain Tubes functioneren als een drain voor spiegel, motorput, livewell of aasput. Gemaakt van messing voor corrosiebestendigheid en voorzien van een flens van 90 graden. Seachoice zet zich in voor het leveren van hoogwaardige maritieme accessoires en OEM-vervangingsonderdelen om liefhebbers van vissen, varen en watersporten over de hele wereld tevreden te stellen. Seachoice wordt gerund voor en door watersporters en biedt een brede productlijn en blijft toch betaalbaar.

Onderdeelnummer fabrikant 50-19111. 90 graden flens. Corrosiebestendig materiaal. 1 inch binnendiameter (ID). 6-inch lange koperen afvoerbuis met .035 wand. Functioneert als afvoer voor spiegel, motorput, livewell of baitwell.
Brand SEACHOICE
Brand Name ‎SEACHOICE
Customer Reviews 4.5 4.5 out of 5 stars 44 ratings 4.5 out of 5 stars
Fishing Technique ‎Spinning
Included Components ‎End Product & Information
Item Dimensions LxWxH ‎2 x 2 x 2 inches
Item Dimensions LxWxH 2 x 2 x 2 inches
Item Package Dimensions L x W x H ‎8.5 x 3.5 x 0.9 inches
Item Weight 0.01 Ounces
Item Weight ‎0.01 Ounces
Manufacturer ‎Seachoice
Material End Product & Information
Material ‎End Product & Information
Model Name ‎19111
Nominal Wall Thickness 3.75 month
Number of Items ‎1
Package Weight ‎0.1 Kilograms
Part Number ‎50-19111
Size ‎One Size
Suggested Users ‎Gender Neutral
Warranty Description ‎Http://www.seachoice.com/warranty-information

3.6

6 Review
5 Star
76
4 Star
14
3 Star
4
2 Star
0
1 Star
6

Schrijf je beoordeling

Uw e-mail wordt niet gepubliceerd. Alle verplichte velden zijn gemarkeerd met*

Scritto da: Rick G
Excellent quality product!
I recently replaced 5 fittings on my boat. I purchased (6) fittings of a shorter length. I had to order three of this brand. The difference in quality of this brand is exceptionally higher than the Seachoice fittings I purchased.
Scritto da: steven
For Boat transum use.
Item is as described & was delivered on time.
Scritto da: matt r.
Quilty brass ok thickness
Used on a Boston whaler where the hull is foamed . The standard size was to short.
Scritto da: squirrel
Not as described.
This tube does not have an ID of one inch. It has an OD of one inch. This was critical for my needs. Very disappointed as I needed the extra amount of interior diameter. It has caused me to rework my project. I would not have purchased the tube if the description had not said that the internal diameter was a full inch in interior diameter.
Scritto da: Casey Jones
Crap junk from China
Cheap brass from China .... will not cut straight ... I've worked with brass for 50 years , new Ridge cutter and the wheel runs . Garbage ! Total waste of money and time
Scritto da: Toolmanazon
Be sure to anneal before installing!!!
Installs well with the correct tool but be sure to anneal the area your going to flare before installing or it wont work. Annealing brass is done by heating red hot with a torch and cooling immediately with water. Use 3M 5200 liberally coat both the drilled hole and the outside of the sleeve before install and your good to go

Gerelateerde producten

Ontdek ons ​​internationale netwerk

We verzenden naar 28 landen, meer dan 200.000 producten. Blijf op de hoogte, schrijf je in voor de nieuwsbrief.

Array