SharkBite 1/2 inch terugslagklep, push-to-connect messing sanitaire fitting, PEX-buis, koper, CPVC, PE-RT, HDPE, U2008-0000LFA 1/2 inch messing

Name: SharkBite 1/2 inch terugslagklep, push-to-connect messing sanitaire fitting, PEX-buis, koper, CPVC, PE-RT, HDPE, U2008-0000LFA 1/2 inch messing
Brand: SharkBite
SKU: 0697285466166
Price: 44.59 EUR
Availability: InStock

Brand:SharkBite

3.8/5

€
44.59

PRODUCTBESCHRIJVING Vereenvoudig uw sanitairprojecten met de SharkBite messing push-to-connect terugslagkleppen. Samengesteld uit DZR gesmeed messing, is deze sanitaire klep corrosievrij en perfect om de terugstroming van water snel en gemakkelijk te voorkomen. Deze messing sanitairfitting heeft een push-to-connect ontwerp dat ideaal is voor het werken in krappe ruimtes en zowel horizontaal als verticaal kan worden geïnstalleerd. Deze push-to-connect-kleppen zijn eenvoudig te installeren, compatibel met PEX-, PE-RT-, CPVC-, SDR-9 HDPE- en koperen buisarmaturen en vereisen geen speciaal gereedschap, lijm, krimpen of solderen voor installatie. Deze veerbelaste terugslagkleppen zijn geschikt voor commerciële reparaties of projecten voor woningverbetering. SharkBite messing terugslagkleppen zijn bestand tegen 200 graden F en 150 PSI. 25 jaar garantie. VAN DE FABRIKANT SharkBite U2008-0000LFA Terugslagklep Algemeen gebruik 1/2-inch veerbelast

Hoeveelheid

Voeg toe aan winkelkar Koop nu

EAN: 0697285466166

Categorieën Tools & Home Improvement, Rough Plumbing, Pijpen, Pijpfittingen & Accessoires, Buisfittingen,

SPECIFICATIES: Gemaakt met DZR gesmeed messing, deze terugslagklep is bestand tegen 200 graden F en 150 PSI. DE VOORKEUR VAN DE PRO: SharkBite-gereedschappen en fittingen voldoen aan dezelfde hoge normen voor commerciële en residentiële sanitaire toepassingen, waarbij duurzaamheid en gebruiksgemak worden gecombineerd, geschikt voor commerciële reparaties of projecten voor woningverbetering. GEMAKKELIJK TE INSTALLEREN: Het innovatieve push-to-connect ontwerp van de SharkBite messing terugslagkleppen zorgt voor een snelle en eenvoudige installatie, zonder gereedschap, krimpen, lijm of solderen; kan horizontaal of verticaal worden geïnstalleerd. VEELZIJDIG: Pushfit veerbelaste terugslagkleppen werken goed met PEX, CPVC, PE-RT, SDR-9 HDPE en koperen leidingen. SHARKBITE MESSING CONTROLE VALVE: Met deze push-to-connect messing terugslagklep kunt u de terugstroming van water snel en eenvoudig voorkomen; ideaal voor werken in krappe ruimtes **Verwijderen met een ontkoppelingsclip of een ontkoppelingstang**.

Batteries Included?	‎No
Batteries Required?	‎No
Brand	SharkBite
Color	‎Brass
Country of Origin	‎China
Customer Reviews	4.8 4.8 out of 5 stars 1,027 ratings 4.8 out of 5 stars
Exterior Finish	Copper,Brass
Included Components	‎Check Valve
Inlet Connection Type	Cross Linked Polyethylene
Is Discontinued By Manufacturer	‎No
Item Dimensions LxWxH	1.06 x 1.06 x 2.6 inches
Item model number	‎GIDDS-272533
Item Package Quantity	‎1
Item Weight	‎0.8 ounces
Manufacturer	‎Cash Acme
Material	Brass
Material	‎Brass
Measurement System	‎Inch
Outlet Connection Type	PEX
Part Number	‎U2008-0000LFA
Product Dimensions	‎1.06 x 1.06 x 2.6 inches
Size	‎1/2 in.
Style	‎Brass Push Check Valve
Warranty Description	‎Limited 25 Year

5 Star

4 Star

3 Star

2 Star

1 Star

Schrijf je beoordeling

Uw e-mail wordt niet gepubliceerd. Alle verplichte velden zijn gemarkeerd met^*

Uw beoordeling

Scritto da: RDV

Worked perfectly on Water Heater

Used this on my tankless water heater. This will prevent any water surge on the cold water side. Which with any water movement on a gas tankless it will come on for just a few seconds. This resolved my issue.

Scritto da: Kevin M.

A little pricey, but worth it.

Not too much to say really, it works exactly as described and exactly as I expected. It was a little on the pricey side, in my opinion, for what it is; but at the same time, I paid it and was very happy to not have to spend a lot longer sweating copper.

Scritto da: C. Davis

SharkBite fittings are so easy to use!!!

Our house is on well water, so we have numerous filters and a water softener. We were noticing that when the water softener regenerated, that their would be air in the lines upstairs the next morning. I'm assuming the cause is a slight drip in our upstairs shower (it allows a very slow drip of water), so when the softener is regenerating, that leak allows the water to backfill from the water lines that run upstairs. When I installed the water softener, I used a SharkBite connector, so all I did was disconnect that join and replaced it with this check valve. So far, that has fixed the issue with the air getting in the lines (although I still need to fix the leak). Note: Removing the old SharkBite union and replacing it with the check valve took about 2 minutes to complete!

Scritto da: Mark Gehring

Fixed my RV shower problem, love it!

Installed this in my travel trailer, in the hot water line of the shower. IF you do this, it will stop the back flow of the cold water back into the hot water line. Then, when you turn the shower head back on, the water will be warm, not cold. I had pretty good access to the water lines behind a little white plastic cover held in with 4 screws. It was a little tight, but no too tough. You need to cut out 3/4" from the line, so that when you put this in, the overall length of the line to the shower will be the same. Took maybe 30 minutes total. No leaks. Keep in mind you can rotate the pipes after pressing this on, so you don't need to be careful with orientation. Also, the Sharkbite website shows how to remove it if you screwed up and put it in backwards.

Scritto da: Amazon Customer

Easy replacement checkvalve.

I replace an old check valve that wasn't holding back pressure anymore. Using a SharkBite unit makes it possible to remove and clean the valve without having to desolder the fitting.

Scritto da: Zac

Good for failed RV demand pump valves

I got this to keep in my RV for emergency repair purposes in the event my demand pump's back-flow valve fails. I've had it happen before, and it's no fun. This should make the fix easy. Although I haven't installed it yet, I've installed all manner of Shark Bite fittings on everything from copper to PVC to pex, and I've never been disappointed. I have high confidence that this one will be no different.

Scritto da: Jefferson S. Osborne

A must have for Tankless Hot Water Installs

I think most folks have their tankless hot water installed in their garage, but if your's is in your crawl space and bothering someone in the room above this is for you!! The flow sensor on my tankless hot water heater would fire up when cold water in the house had not been run in a few hours. With my tankless installed under my bedroom floor in my crawl space it was annoying that the tankless hot water heater would fire up in the middle of the night when someone would flush a toilet. Once the toilet was filled and the water stopped running it was sending a water pulse through my cold water lines that would cause my tankless to fire up for just a minute. A false start you might say. I installed this valve on my cold line before it connected to the inlet on my tankless hot water heater. Problem solved!!!!! Now my tankless only fires up when the hot water is ran in my house. Buy a disconnect clip while your ordering along with a deburring and depth tool. I used both during my install with Pex.

Scritto da: Amazon Customer

Easy to install.

I have had to replace the 12 volt fresh water supply pump in my trave trailer several times because the internal check valve fails after just a few months. Every time the check valve fails it fills, then overflows the fresh water tank. I decided this time not to replace a perfectly good pump over a non working check valve. I purchased a threaded check valve to direct attach to the pump, but the male/female threads were backwards from what I needed. I could have replumbed things, but the Shark Bite check valve was much easier to install. It was simple to cut the line, and then press the Shark Bite on. Time will tell as to how long this will hold the pressure.

Scritto da: John H.

avoid water backflow

easy to install and work excellent

Scritto da: Mat Loiselle

Expensive but easy to install and work well

I have separate hot and cold hose bibs in my garage. They're connected together with a mixing hose so that I can get any temperature into my garden hose. I installed these on both the hit and cold side to keep the tap with the higher pressure from back feeling into the other open tap. I used these rather than vacuum breakers because the vacuum breakers release the water to atmosphere which would make a mess in the garage. They're expensive for what they are, but they're doing their job well so far!

Scritto da: Danegeld

That it has a sound reputation for reliability.

Very easy to fit, seal is perfect, should last for many years.

Scritto da: sci-fi fan

good product

Installed in minutes, no leaks and low profile. Very satisfied!

Scritto da: Rick lee

does the job but at the cost of flow rate

when I used the connection with this valve inline I got 1.8 Gpm. when I placed it on a different return line the main line got 4.0 Gpm. that is a huge loss for a 1" check valve.