Teach Tech "Hydrobot Arm Kit", Hydraulische Kit, STEM-bouwspeelgoed voor kinderen vanaf 12 jaar

Brand:Elenco

3.6/5

€
120.95

Jonge ingenieurs zullen blij zijn met de nieuwe HydroBot Arm Kit. Hij wordt aangedreven door water, dus geen motor nodig! Ze kunnen de hendels en de kracht van de hydrauliek gebruiken om de meerassige arm te bewegen. De hendelcontrollers hebben een speciaal remsysteem dat helpt bij het uitvoeren van fijne, nauwkeurige taken. De grijper kan openen en sluiten met een opening van maximaal 47 mm (1,89 inch), polsgewrichtrotatie van 180 graden. , polsgewrichtmobiliteit van 98 graden. , ellebooggewrichtbereik van 44 graden. , basisrotatie van 270 graden. , en beweging van het schoudergewricht van 45 graden. , met een verticaal bereik van 16. 35in. , horizontaal bereik van 12. 42in. , en 50g hefvermogen. Grijpers kunnen worden verwijderd en vervangen door zuigcomponenten om voorwerpen op te pakken met een glad oppervlak van niet meer dan 50 g (1,75 oz.). De duidelijke, geanimeerde instructies maken de montage en bediening van deze STEM-robot gemakkelijk te begrijpen. Meest geschikt voor toekomstige ingenieurs van 12 jaar en ouder. Elenco Teach-producten zijn gebaseerd op STEM-activiteiten (Science, Technology, Engineering, Math) om kinderen te onderwijzen en aan te moedigen in hun ontwikkeling, terwijl ze plezier hebben! Alle Teach Tech Green-Energy-robots worden aangedreven door water, wind of zon, dus er zijn geen batterijen nodig. Perfect voor toekomstige ingenieurs vanaf 12 jaar.

Hoeveelheid

Voeg toe aan winkelkar Koop nu

EAN: 0756619012728

Categorieën Toys & Games,

HANDS ON LEERPLEZIER: Teach Tech-producten richten zich op STEM-activiteiten (wetenschap, technologie, engineering, wiskunde) om kinderen te onderwijzen en aan te moedigen in hun educatieve ontwikkeling, en dat allemaal terwijl ze plezier hebben!. NIET ALLEEN ROBOTICA: Met onze Teach Tech Kits stopt het leren niet alleen bij robotica. Teach Tech-instructies zijn specifiek ontworpen om probleemoplossende vaardigheden, analytisch denken en nieuwsgierigheid bij jonge geesten te ontwikkelen. BEWEEGT, DRAAIT EN GRIJPT: Gebruik de hendels om de grijper te bedienen die kan openen en sluiten of kan worden vervangen door zuigcomponenten om voorwerpen op te pakken. AANGEDREVEN DOOR WATER: Gebruik de kracht van hydrauliek om de Hydrobot te gebruiken en te besturen! De arm heeft 6 verschillende assen en kan tot 270 graden draaien - geen batterijen nodig. BOUW WERKROBOTS: Leer je kinderen werktuigbouwkunde op een manier die ze niet kunnen weerstaan! Deze kit is ontworpen voor kinderen van 12 jaar en ouder en begeleidt je leerling door het proces van het bouwen van echte, werkende robots - onderwezen op een manier die ze zullen begrijpen!.

Age Range (Description)	Kid
Brand	Elenco
Country of Origin	Taiwan
Customer Reviews	4.5 4.5 out of 5 stars 1,151 ratings 4.5 out of 5 stars
Item Dimensions LxWxH	15.6 x 11.4 x 4.1 inches
Item model number	TTR-632
Item Weight	2.75 pounds
Manufacturer	OWI Inc
Manufacturer recommended age	12 years and up
Product Dimensions	15.6 x 11.4 x 4.1 inches
Release date	May 20, 2019
Size	Pack of 1
Theme	Cartoon

5 Star

4 Star

3 Star

2 Star

1 Star

Schrijf je beoordeling

Uw e-mail wordt niet gepubliceerd. Alle verplichte velden zijn gemarkeerd met^*

Uw beoordeling

Scritto da: Lois

Technical toy

Was a present foot grandson and he loved putting it together.

Scritto da: Leroy H.

Awesome gift and Price tooo (but bad Amazon delivery)

This is a perfect gift and price (on sale). Only 4-Stars as the shipper did not box the item which was a gift, but put a label directly on the gift itself (which could not be removed clean). Additionally, Amazon delivery left the box on the wet porch deck instead on the dry delivery table 2ft to the left, thus the box was wet and warped, not very giftable l!!! :-( Soo then no way to return and get a new one before the birthday party, soo it is what it is. Also, no option to file complaint/put a note in to anyone on it.

Scritto da: Frank

A nice, if small, workable robot arm to show principles.

Start to finish assembly took right at 8 hours, spread over 3 days. I am a moderately skilled senior citizen. This is no trivial assembly. The good news is that the instructions are very clear, and the parts generally fit together well. However, assembly requires *close attention* to the images/directions, which can wear you down if you try to do it in one sitting. I am tracking my hours to see how long the whole assembly takes, and will share those later. Some hints: 1. DON'T throw away the little envelope that says "don't eat this". I thought it was some kind of dessicant but it is oil essential to project. 2. You will need a *small* phillips screwdriver, with bit fits screw heads well, because some are tight. Lots of pressure and slow turning of screwdriver was necessary for many of the screws. 3. Put a new blade in your utility knife to trim off the innumerable tabs. Update - carefully cut items from matrix with knife to avoid separate removal of tabs 4. Be methodical, and careful with the **small** parts (and tiny screws). Put items in ziplok bags & containers as you go. No spare screws or springs are provided so DON'T LOSE any. (I'd have paid the extra $0.20 or whatever) 5. Filling the pneumatic system components with water was the most nerve-wracking - mainly because of the difficulty of eliminating water bubbles. I suggest getting a large container for water, big enough to submerge your hand and enable you to hold items upside down when filling. Move plungers multiple times to eliminate air from cylinders. 6. The filling instructions were a little confusing to me, but basically they want you to fill the cylinders BEFORE attaching hoses. They don't tell you explicitly but I think their procedure is designer to minimize bubbles in tubes that you fill with water. 7. Hoses are very slippery when wet and hard to push on all the way, but a BIG help was using a high-tech "wicking" sweat rag - the artificial fiber gave a good grip on tiny pipe. Also good for mopping up spills. 8. I tried to fill the little hoses by gravity flow before connecting to cylinders, rather than when they were dry. Little bubbles tend to form in dry pipe when first wetted. Maybe it helped a little. Oh, and yes, trying to correct big bubbles later, after complete assembly would be a nightmare - so do your best while filling initially. 9. Installing the levers and cylinders in the base unit is easiest to do from the bottom, rather than from top as they show. I was sure I was going to crack the plastic several times when pushing cylinder assembly ( the enc with spring) to lock under/into control lever. It is very tight but never broke. 10. The unit worked OK when finished - it won't replace a robot arm in a GM factory, but it is simple to use and will hopefully be entertaining to 4 year olds. Time will tell if it is durable enough for that age user.

Scritto da: Niles Stonne

Great, Functional Hydraulic Arm

This took my son and I several hours to assemble and went together really nicely. I'm impressed with how functional it is! We've picked up and manipulated all sorts of different toys. Lots of fun!

Scritto da: Amazon Customer

Great gift for kids that love to build.

Gave as a gift to my nephew. He loved building and using it. He is 10. He loves building and constructing challenging things! Perfect gift to give to him.

Scritto da: dave

Potential leaks

First I like this robot very much, gave as gift to grandkids and had fun working with them on rather lengthy assembly. But it was great so they could see and understand how hydraulic systems work. I think we either did not get or lost any lubricant which may have been included and that led to problems with lines popping off , pistons sticking, and air being introduced into system, making arm unusable without bleeding. In some cases rubber piston caps dislodged from piston shaft and had to be extracted. That part was undesirable as kids stop playing with toy when it is “broken”. So I purchased separately little spring clamps (see photo) and disassembled and greased the pistons using water faucet grease. This has greatly improved function of the device. In fact if manufacturer is reading this, hope they take it as a suggestion to provide hose retainer clips with future kits- I doubt it would add more than 50 cents to their production cost and would reduce “complaints” such as this. But overall I want to say it is great that there is an affordable kit for kids to create and learn hydraulic systems with!

Scritto da: Concerned parent

Gifting - hopefully similar to armatron

Kids were at a vintage toy store where an armatron from the 80’s was set up for them to play with. My son fell in love with it and stayed there playing with it for almost an hour. Hoping this is a like for like since armatron is history and impossible to purchase a working one at a reasonable price. Bought as a gift - will update review after use.

Scritto da: Jason Sherer

Great kit.

My son and I worked on this for 2 days and everything is totally functional. Great gift......great chance for some one on one tinker-time.

Scritto da: RIGOBERTO L O

Genial!

Un excelente regalo para niños con inquietudes hacia la ingeniería! Los divierte y reta armándolo y jugando con él!

Scritto da: Maria Contreras

Muy delicado

Está muy padre, lo que los niños aprenden es mucho. Lo que no me gustó fue que es algo delicado para que un niño lo arme. Las piezas se rompen con facilidad