CURT 56334 Voertuig-Side Custom 4-Pin Trailer Kabelboom, Past Select Dodge Nitro, Jeep Liberty, Zwart

Name: CURT 56334 Voertuig-Side Custom 4-Pin Trailer Kabelboom, Past Select Dodge Nitro, Jeep Liberty, Zwart
Brand: CURT
SKU: 0612314563340
Price: 113.32 EUR
Availability: InStock

Brand:CURT

3.7/5

€
113.32

STOFKAP. Om langdurig gebruik en weersbestendigheid te bevorderen, wordt deze 4-polige kabelboom voor aanhangerverlichting geleverd met een rubberen stofkap. Hij past gemakkelijk op de 4-weg platte connector wanneer hij niet in gebruik is, en beschermt hem tegen de elementen buitenshuis. BETROUWBARE KRACHT. Deze 4-weg kabelboom voor aanhangers is gebouwd met technologie voor opbouwmontage. Dit type circuit genereert minder warmte, optimale lichtintensiteit en duurzame prestaties. VOERTUIGSPECIFIEK. Deze aftermarket-kabelboom voor voertuig-aanhangwagen is ontworpen voor geselecteerde jaren van de Dodge Nitro en Jeep Liberty. STANDAARD CONNECTOR. Deze plug-in 4-voudige aanhangerbedrading kan worden gebruikt voor het aansluiten van aanhangerachterlichten, remlichten en richtingaanwijzers. 4-weg bedrading voor aanhangwagenverlichting is populair op een verscheidenheid aan aanhangwagens, waardoor veelzijdige trekmogelijkheden voor uw voertuig worden toegevoegd. MAKKELIJK TE INSTALLEREN. Niet snijden! Geen splitsen! Deze kabelboomset voor een aanhangwagen kan worden aangesloten op de bestaande fabrieksbedrading van uw voertuig en is uitgerust met een standaard 4-pins aanhangwagenbedradingsconnector aan de achterkant voor het aansluiten en trekken van een aanhangwagen.

Geen eenheden beschikbaar

EAN: 0612314563340

Categorieën Home & Garden, Tiers, Towing Products & Winches, Hitch Accessoires, Wiring,

Brand	CURT
Brand	‎CURT
Country of Origin	‎Philippines
Customer Reviews	4.7 4.7 out of 5 stars 281 ratings 4.7 out of 5 stars
Exterior	‎Painted
Item Dimensions LxWxH	9 x 6 x 3 inches
Item model number	‎56334
Item Weight	‎1.81 pounds
Manufacturer	‎CURT
Manufacturer Part Number	‎56334
Material	Rubber
Model	‎Custom Wiring
OEM Part Number	‎56334
Product Dimensions	‎9 x 6 x 3 inches

5 Star

4 Star

3 Star

2 Star

1 Star

Schrijf je beoordeling

Uw e-mail wordt niet gepubliceerd. Alle verplichte velden zijn gemarkeerd met^*

Uw beoordeling

Scritto da: Christian Triplett

Quailty is great

I was a little hesitant about buying one of these because previous module installs didn’t work for me. However I bought this on a whim for my camper and it is has worked since day 1. It took a bit to install it cleanly. But I have had no issues with my trailer wiring since. It caught me off guard when I saw that the trailer turn signal will flash alternate to the car when the brakes are applied at the same time as the turn signal. But I’ve been running it for a few months without issue!

Scritto da: Marcos Santiago

Perfect fit

Installed in less then 30mins.

Scritto da: P K

Works as it should in 2009 Jeep Liberty, a bit of a challange to install (vehicle issues)

Trailer wiring harness was overall a good product for a good price. Installation was a bit of a challenge in several areas, but this is more of a Jeep/vehicle issue than the wiring harness fault. Not much room in the rear tail light areas for the 2 extra connectors. The instructions call for mounting the module under/outside the vehicle, but I mounted the electronic module inside the vehicle (in the jack compartment), and had to cut the factory rubber plugs where the vehicle wires go through the body to the tail lights in order to make these connections. Also, I had to remove several inside plastic body panels in order to fish the main power wire from the engine compartment to the rear of the vehicle. (HINT: Rubber plug in firewall where clutch rod would be if a manual tranny. No rod (easy access) if auto tranny.) One concern: I measured 0.3 volts from each of the 3 "Light" wires to ground even when the vehicle is not running. I'm sure this is something with the electronic switching of the module. A disconnect switch could be installed in the power wire when not using to eliminate this issue.

Scritto da: Gary G.

A Must-have accessory for DYI installers.

This harness was easy to install on my 2011 Liberty. There was plenty of room in the tail light recess for the extra plugs and wiring. The routing of the power line to the battery was a bit of a challenge to avoid the moving parts of the rear suspension and the exhaust system but it can be done with care. My only minor complaint is with the module. Even though I found a flat painted surface and cleaned it extremely well, the double sided mounting tape became loose within hours. I was able to secure the module using the mounting tab on the one end, but additional mounting tab(s) would be preferable.

Scritto da: Edward P.

Fit meant

Great price worked as it should and fast delivery

Scritto da: Lionel A Richard

Instructions clear but you do need some experience in automotive electrical wiring

Easy to install

Scritto da: Christa L. Barnes

Easy to install

Easy installation, clear directions

Scritto da: Jason J McKoy

Plug and play almost.

The product is great it sure beats the old days of splicing in the wires take your time and dont usse the double sided sticky tape to hold up the controller tou might get a 1/4 mile before it falls off self tap it in!

Scritto da: David P.

Easy to install

Product was easy to install. Trailer lights now work perfectly.

Scritto da: Cityslicker

Perfect wiring harness for my jeep

Delivery was on time. Plus easy installation and worked the first time.

Scritto da: Carrie

Wiring Harness Drained Battery

I hooked this up in August to my 2008 Jeep Liberty, which I only use to pull a trailer in the summer. After the Jeep sat for a couple of weeks at the end of the season, it wouldn't start. The Curt custom wiring harness 56334 is drawing constant power, and drained my battery (which was brand new in June). When I remove the fuse from the wire that goes to the unit, the battery is fine as it doesn't draw power, and the Jeep starts every time. I believe I have a faulty unit and would like it to be replaced as it should not draw power when not in use. I can't find any contact information for customer service. I am hoping that Curt Manufacturing will reach out to me to make this right.