D-Link wifi-waterleksensor en alarmstarterkit, systeem voor het hele huis met app-melding, netvoeding, geen hub vereist (DCH-S1621KT) Watersensorkit V2

Brand:D-Link

3.3/5

103.38

De Water Leak Sensor Starter Kit is een gebruiksvriendelijke doe-het-zelf-lekdetectieoplossing voor in huis die u op de hoogte stelt van waterlekken zodra ze zich voordoen, zodat u kostbare reparaties aan waterschade door onopgemerkte lekken kunt voorkomen. De kit bevat een master-unit (of hub) met een bevestigbare detectiekabel en een detectiepod op batterijen. De hub kan op elk stopcontact worden aangesloten, terwijl de sensorpod kan worden geplaatst op plaatsen die gevoelig zijn voor waterlekkage, zoals de wasmachine, de boiler en onder de gootsteen. De Pod heeft twee vooraf geïnstalleerde AAA-batterijen voor een batterijlevensduur van maximaal 5 jaar. Beide units zijn supereenvoudig in te stellen en zijn vooraf gekoppeld aan de mydlink-app die kan worden gedownload op uw smartphone en eenvoudig kan worden verbonden met de bestaande wifi in uw huis. Het multi-alarmsysteem (hoorbaar, visueel, mobiel) maakt het toegankelijk, zowel thuis als onderweg. Het LED-stroboscooplicht van de Hub is krachtig voor visuele meldingen, terwijl het ingebouwde 100 dB-alarm van de Hub gemakkelijk te horen is. U kunt ook verbinding maken met Google Speaker voor gesproken meldingen en ten slotte worden uitgebreide meldingen naar uw mobiele telefoon verzonden. Schaalbaar en veelzijdig, u kunt tot 16 pods in uw hele huis toevoegen. Het onopvallende ontwerp van de pods maakt het gemakkelijk om discreet te plaatsen en de detectiekabel zorgt voor meer onbereikbare plaatsing. De betrouwbare mydlink-watersensorkit staat altijd aan, dus als u weg bent, hoeft u zich geen zorgen te maken.

Niet compatibel met DCH-161-US (batterijgevoede versie). Sensor Pod(s) maken gebruik van een Sub-Gigahertz-band voor betere dekking en connectiviteit in gebieden waar wifi niet kan doordringen, zoals de kelder. Master Sensor wordt aangesloten op een stopcontact en maakt verbinding met uw wifi thuis. De externe Sensor Pods worden gevoed door twee AAA-batterijen (meegeleverd) met een levensduur van maximaal vijf jaar. Eenvoudige installatie en plaatsing: Master Sensor Plug maakt gebruik van een 1,5 meter lang snoer met een bevestigbare 1,5 meter lange watergevoelige kabel. Breid de dekking draadloos uit tot 16 gevoelige gebieden, zoals naast waterverwarmers, wasmachines en onder gootstenen met Sensor Pods (DCH-S163). Waarschuwingen omvatten krachtige LED-stroboscoop, ingebouwd alarm van 100 dB, meldingen voor mobiele telefoons en gesproken meldingen met Google-luidsprekers die realtime meldingen bieden, waar u ook bent. Voorkom kostbare waterschade: Master Sensor Plug-in met een compacte, waterdichte Sensor Pod (DCH-S163) detecteert lekken; multi-waarschuwingssysteem (spraak, alarm, tekst) waarschuwt u meteen.
Batteries 2 AAA batteries required.
Brand D-Link
Color White
Country of Origin China
Customer Reviews 4.2 4.2 out of 5 stars 209 ratings 4.2 out of 5 stars
Item Dimensions LxWxH 2.25 x 2.32 x 2.19 inches
Item model number DCH-S1621KT
Item Weight 5.1 ounces
Manufacturer D-Link Systems, Inc.
Number of Batteries 2 AAA batteries required.
Number of Batteries 2 AAA batteries required. (included)
Power Source Battery Powered
Product Dimensions 2.25 x 2.32 x 2.19 inches

3.3

4 Review
5 Star
65
4 Star
15
3 Star
5
2 Star
5
1 Star
11

Schrijf je beoordeling

Uw e-mail wordt niet gepubliceerd. Alle verplichte velden zijn gemarkeerd met*

Scritto da: Wesley Dean
detects water but the notifications are irregular; won't talk to Home Assistant
When the probe gets wet, it triggers the alarm as-expected. However, the period between state changes (e.g., going from wet to dry or dry to wet) is way, way, way too short. As a result, when the probe gets wet, it vacillates between wet and dry multiple times per second and each time resulting in a notification being generated. That is, the alarm chirps in an almost strobe-like manner and my phone "blows up" with multiple notifications per second. I'm extremely reluctant to configure a "designated contact" with a phone number. I understand that the contact is notified when a button is tapped on the notification (i.e., it's not automatic), I don't trust the app to stay within its walled garden. The wired device (DCH-S162) supports integration with Alexa and Google Assistant. This is configured via the MyDlink app. This leads me to believe that there is some kind of API or MQTT support by which the device communicates; however, there is not (yet) support for Home Assistant. There is support for the DCH-S160 via 3rd party integration; however, that integration doesn't support the DCH-S161. Moreover, the product listing asserts that this device is not compatible with the DCH-S161 which leads me to believe that there is yet another variation in communication mechanisms. (i.e., if Home Assistant supported the DCH-S161 and this device was compatible with DCH-S161s, it may be possible to get Home Assistant to talk to it). If the device was supported by Home Assistant, one could trigger notification upon continued state of water detection *for more than 5 seconds* to resolve the aforementioned notification issue; similarly, it could be used to trigger a secondary pump to run. But it doesn't, so I can't. If I were to do this project over again, I would likely go with a SOC device (e.g., a Raspberry Pi) that I could control; however, for a typical consumer, I suspect that this device would be sufficient.
Scritto da: P. Koskiniemi
Easy set up. Excellent customer support!
I read the reviews of people having trouble pushing the set buttons on the back of the sensors when pairing. The easiest solution is to push the button firmly with the rounded end of a ball point pen cap for about 2-3 seconds and you will get the light! The setup and pairing are very easy. Be advised that you must have a smart phone for set up and that the notifications are limited to push notifications through the mydlink app. No text, email, or phone notifications are available. All things considered this product is very reasonably priced and the sensors work well. The sensors are small enough to fit under your dishwasher and refrigerator, and the cable sensor is perfect for going under the washing machine.
Scritto da: Iainsmith
A Very Disappointing Product
I read a review in a trusted New York newspaper that rated the d-Link DCH 162 hub and DCH 163 water leak sensors very highly. I needed water leak protection so I bought the package on Amazon and subsequently purchased a 3-pack of sensors from d-Link (not available through Amazon). The first problem I noticed was how difficult it is to put the sensors into pairing mode. You have to stand close to the hub and press the pairing button on the bottom of the sensor with all the finger strength you have. I paired 4 sensors and they were all tough to activate. The mobile app walks you through the set up, which is pretty easy. I changed the system-generated sensor ID to the locations of where the sensors were placed. For example DCH-S163-0E48 was changed to 3rd floor bathroom. Unfortunately the app still shows the original number instead of the label on 2 of my 4 devices. If I drill into the device details it shows “3rd floor bathroom” but not on the home page where I need it. The labels seem to change around so I suspect it’s a bug in their software. Last week one of my devices displayed in the mobile app as off-line. The device had been placed behind a stacked washer / dryer and wasn’t accessible without moving the machines. When I drilled into the detail of the device from the Home Screen of the mobile app the status showed as being in power-save mode. I called d-Link support and was told not to worry about the off-line status on the Home Screen. I was assured that it would still sound an alarm if water were detected. I was not convinced since the other 3 sensors showed as being in power-save mode from the Home Screen. I eventually moved the machines, removed the device through the app and set it up again. It now shows correctly as being in power-save mode. When I first set up the hub I enabled notifications and ran the recommended water test and after an initial notification failure re-ran the test was notified on my phone of a water leak. This was great except when our water actually leaked under the kitchen sink today and I was out of the house I didn’t receive a notification . I did, however, receive a frantic call from my wife about water pouring onto the kitchen floor. I could hear the alarm in the background (very loud). When the alarm first sounded she ran upstairs thinking we had a leak under the washing machine only to discover it was in the kitchen when she came back downstairs. She asked why the system didn't tell us the location of the leak; good question. I’m hoping my experience with this system improves. Right now I have little confidence in either their mobile app or support. I’m disappointed in d-Link.
Scritto da: Horn player
Make sure you test it and the app.
Pleased with it. It would be good if the email message would trigger an alarm on the phone. It is easy to miss the email. Maybe the email notificaton could trigger a ring tone, like a fire alarm. I tried to figure out how to do it without success. That would be a great feature. If anyone out there can figure out who to do that, I would like to know. Thanks.

Gerelateerde producten

Ontdek ons ​​internationale netwerk

We verzenden naar 28 landen, meer dan 200.000 producten. Blijf op de hoogte, schrijf je in voor de nieuwsbrief.

Array