0
0

Totaal:€ 0.00

Zie winkelwagenUitchecken
LoginRegister
0

Totaal:€ 0.00

Zie winkelwagenUitchecken
LoginRegister

TANDWIELSLEUTEL Trekkerset stuurbekrachtigingspomp - 41560D

Brand:GEARWRENCH

3.7/5

€
86.20

Onderdeelnummer 41560 is stopgezet door GearWrench en vervangen door 41560D; wanneer de huidige voorraad van de 41560 op is, wordt deze vervangen door onderdeelnummer 41560D. Verwijdert en installeert stuurbekrachtigingspomppoelies van de meeste binnenlandse voertuigen. Bevat de benodigde adapters voor onderhoud aan GM 3.1 L, 3100, 3400 en 3800 V6-motoren, GM 2.3L Quad 4 viercilindermotoren en Ford 4.6L, ​​5.4L en 5.8L modulaire V8-motoren. Past op katrolnaven met een diameter van 1-1/8 inch, 1-1/4 inch, 1-5/16 inch en 1-3/8 inch.Inclusief snelkoppelingsgereedschap voor GM 1/2, 3/4 en 1 ton pickups.Inclusief KDT3893 ontkoppelingsgereedschap; KDT41561 bus- en schroevenset en de KDT41562 bus- en schroevenset. KD Tools 41560 poelieset stuurbekrachtigingspomp

Hoeveelheid
Voeg toe aan winkelkarKoop nu

EAN: 082171041563

Categorieën Home & Garden, Vervangingsonderdelen, Riemen, Slangen & Katrollen, Pulleys, Power Pulleys,

Inclusief snel los te koppelen gereedschap, bussen en schroevensets. Inclusief adapters voor verschillende voertuigmodellen. Gebruik voor installatie en verwijdering. Poelieset voor stuurbekrachtigingspomp voor de meeste binnenlandse voertuigen.
Batteries Included? ‎No
Batteries Required? ‎No
Country of Origin ‎China
Customer Reviews 4.6 4.6 out of 5 stars 519 ratings 4.6 out of 5 stars
Finish ‎Black Oxide
Is Discontinued By Manufacturer ‎No
Item model number ‎41560D
Item Package Quantity ‎1
Item Weight ‎2.2 pounds
Manufacturer ‎GEARWRENCH
Material ‎Steel
Measurement System ‎English/Standard
Part Number ‎41560D
Product Dimensions ‎9.75 x 8.5 x 2 inches

3.7

8 Review
5 Star
76
4 Star
15
3 Star
5
2 Star
1
1 Star
3

Schrijf je beoordeling

Uw e-mail wordt niet gepubliceerd. Alle verplichte velden zijn gemarkeerd met*

Scritto da: Jim Smith
Works good but needs shorter shaft
Yes it works good but it needs a shorter bolt in order to put the pulley back on a GM power steering pump .You have to install pulley on the power steering pump after it is mounted to engine and you need a shorter shaft/bolt to install.This was for a 2002 monte carlo ss. There is no room to remove the power steering pump without removing the pulley I tried from the top and the bottom you must remove pulley first
Scritto da: Ted Jarosinski
Better quality at a reasonable price
I have another cheap version of this set from the chinese tool store and it is nowhere near as good. For the price the quality of this set is nice and if you don't abuse it I think it will last a long time. I made sure to grease the threads and any of the moving parts on the tool before I started, which is important with any kind of tool like this. As mentioned in some other reviews, there are ball bearings in some of the pieces of this tool, so when taking them apart do it over a rag so the ball doesn't escape. They really help to reduce friction, which is helpful when fighting with a power steering pulley that is a tight fit. I used this kit to change the power steering pump on 1994 Ford Explorer. If you take the fan and shroud out (don't forget you need the fan clutch wrench set to do this) there is enough room to use the tool. I had to use two wrenches linked together on the tool to get enough leverage. It's a good arm workout by the time you get the pulley off and then new one back on, but it worked well and I had no problems using it.
Scritto da: Palmer
Works as intended!
After having having the summer of "everyones power steering pump dying" I finally bought one, it saved me in gas from driving to the parts store about 6 times this past year. Wish they would just include the pulley on the remanned part.
Scritto da: Ross
Bummed
The pulled works like a champ have used several times. As for the install. Junk. Used once and the first time just completely stripped out. Been trying to get ahold of gearwrench for a few weeks but I think there website is down and there phones because I can’t through with either
Scritto da: S. A. ROBBINS
Worked fine pulling a pulley off a GM power steering pump.
Used this tool to pull a pulley off a GM power steering pump and it worked with no problems. Just make sure you put the angled end of the jaws on the pulley.
Scritto da: underhill
Perfect
I needed this too ajust my power steering pulley,it was out of alignment.I was skeptical about ordering it with no instructions,but I was sick and tired of my belt chirping,and garage, after garge insisting it was related to the belt tensioner, or the idler pully.After replacing all those parts and a new alt,the chirp disapeared but only for a few weeks,then it came back. So I decided to get the KD 41560,to ajust the power steering pulley.This was my last hope of stopping the chirp. It workded perfectly on my 99 GMC Sonoma. It was tough ajusting with the fan still attached but, it's doable.As far as instructions.If you can't figure it out,you probably shouldn't be working on vehicals.There are only a few parts in the kit, and they work one way.But it would be alittle easyer to include a small manual for novice users,but if I can do it, anyone can.The chirping is gone. KD is a very good, push, pull pulley kit.It held up to the task .Very pleased that I bought this.Coming from someone who hates working on vehicals. A+ KD.
Scritto da: howard
Worked good
Did what I needed it to do
Scritto da: MARNAV
A good tool but could be better with minor changes..
All in all, seems like a good tool but I have a few things I would change myself. This needs an instruction card of some kind included. KD, are you listening? Couldn't cost more than say 50 cents or so for us who aren't mechanics by trade. I'm using this on an 83 Delta, the puller did work well. Two of the center threaded pulling/pushing pieces have ends that will come off, and underneath is a load ball bearing that will fall out and roll away and then you can't use it without another ball bearing, guess how I found that out KD? A warning on the card would be nice. My last observation is the installer tool for GM, the 9/16 or so size used simply is too flimsy, these pulleys are on very tight I know mine was. A standard Snap-On 9/16 wrench is too short, hurts your hands. Why not just make it simple and use 3/4 - 19mm on everything guys? This could be a 5 star tool with minor changes. How about it KD? Up the price a few bucks and make those changes and you have a 5 star tool. 3 star is all I could give it.

Gerelateerde producten

hot
TANDWIELSLEUTEL Trekkerset stuurbekrachtigingspomp - 41560D
3.7/5

€ 86.20

TANDWIELSLEUTEL Trekkerset stuurbekrachtigingspomp - 41560D
3.7/5

€ 86.20

Ontdek ons ​​internationale netwerk

We verzenden naar 28 landen, meer dan 200.000 producten. Blijf op de hoogte, schrijf je in voor de nieuwsbrief.

Array

Totaal:€ 0.00

Zie winkelwagenUitchecken

Categorieën

Alle categorieën
Menu Categorieën In de buurt van Winkelwagen

Menu