Ultra-Fab 48-979023 2,5 x 3 gelaste jumborol

Brand:UF Ultra-Fab

3.7/5

119.54

Eén per pakket. Las op zware 1/4 stalen montagebeugel. Voor alle campers, aanhangwagens en 5th wheel RV's. 2,5 wielbreedte, stalen rol met 3 wieldiameters.

Eén per pakket. Las op zware 1/4 stalen montagebeugel. Voor alle campers, aanhangwagens en 5th wheel RV's. 2,5 wielbreedte, stalen rol met 3 wieldiameters.
Brand UF Ultra-Fab
Exterior Alloy Steel
Item Diameter 2.5 Inches
Item Weight 2.85 Pounds
Material Alloy Steel
Size 2.5 Inch x 3 Inch
Vehicle Service Type Trailer

3.7

8 Review
5 Star
84
4 Star
9
3 Star
3
2 Star
0
1 Star
3

Schrijf je beoordeling

Uw e-mail wordt niet gepubliceerd. Alle verplichte velden zijn gemarkeerd met*

Scritto da: Kells.
Saved me from expensive driveway work.
So we have a tilted driveway that has a gated entrance to enter our backyard. It’s a hard approach angle. The first time entering we made it, the first time exiting we scraped hard and severely damaged the rear stabilizer electric jack system. I tried the swivel wheel rollers first and shattered one on the first exiting. Moved to these rollers. We welded them to the rear hitch. This saved us. The product is strong. I can enter and exit the yard without worry now. We have a Thor 26.5 motor home. We gently touch down. Roller makes contact for about 3 feet. Perfect. Go slow. Go straight. You’ll make it now.
Scritto da: Lotus54
Very stout, but bolt going through is quite loose.
The through bolt is very loose in the roller pin. It is setup with a grease fitting- but I don’t think any grease would actually get into the needle bearings since it is so loose. I may make a larger diameter bolt to solve it issue.
Scritto da: Tom L.
Beefy
Working on a project for a friend, we welded these to the back bumper of a sprinter van in order to protect the custom generator mounted beneath the vehicle. Driving up steep inclines, the length of the vehicle presents a high probability the tail will drag. With the generator mounted underneath, it could be damaged or ripped off the vehicle completely. We welded 2 1/2” square tubing “posts” made from 3/8” thick steel to the wheels and then welded those to the van’s aftermarket trailer hitch, ensuring the wheels were slightly lower than the lowest point on the generator. After a couple of test runs in steep driveways, the wheels worked perfectly.
Scritto da: James E. Gunderson
Sorry, have not tried it yet
Modified bracket cut it off and put the roller on the sides of the bracket and welded it. Bracket on right, cut it and welded a plate across the 2 legs hanging down the bracket, see the roller in the left picture
Scritto da: reno 64
Great product
Heavy duty and good quality. Works great on my 5th wheel
Scritto da: Stephanie Gilbert
Must buy for big trailers
We purchase these rollers for the back of our 40 ft trailer. We had them welded on before we used the trailer to move our four bedroom house from Florida to Maine. These rollers saved our buts several times on the trip. If we did not have them the would have done severe damage to not only the trailer but also the contents with in.
Scritto da: myndimcmahon
A need to have
It saved us from scrapping the crap out of the back of our enclosed trailer. Thank God for these wheels. So worth the money.
Scritto da: Lisa Andersen
Super heavy duty
EXCELLENT quality skid wheel. Would not have gotten my trailer up my new driveway without them. My trailer is a 16'x8'x8' cargo trailer. My driveway is so steep that both trailer axles were off the pavement while these skid wheels rolled right up the driveway to allow the trailer to transition onto the steep driveway with about 7,500 lbs in the trailer! Great product, super fast shipping, easy weld on install!

Gerelateerde producten

Ontdek ons ​​internationale netwerk

We verzenden naar 28 landen, meer dan 200.000 producten. Blijf op de hoogte, schrijf je in voor de nieuwsbrief.

Array