Weiler 56490 montagedoorn voor doorslijpschijven met 3/8 asgat, alleen 1/4 steeldoorn

Brand:Weiler

3.7/5

37.00

De Weiler 56490 doorn monteert veilig een Type 1 doorslijpschijf met een 3/8 asgat op een slijpmachine die 1/4 stelen accepteert. De doorn is ontworpen om te passen op 0,035 tot 1/4 dikke doorslijpschijven en is gemaakt van koolstofstaal voor sterkte en een langere standtijd. De doorn bestaat uit een schacht en een schroef. De schacht wordt in een slijpkop gestoken. Het doornuiteinde van de schacht is geschikt voor een doorslijpschijf en het schroefgedeelte van de doorn wordt in de schacht geschroefd, waardoor het wiel aan de doorn wordt bevestigd. ontbraam- en afwerkingsindustrieën. Merit, opgericht in 1945 en met het hoofdkantoor in Cleveland, OH, voldoet aan de normen 9000 en 14001 van de International Organization for Standardization (ISO).

Klik op de Weiler-link bovenaan deze pagina voor meer informatie over ons 4e generatie familiebedrijf met hoofdkantoor in Cresco, PA. Inkeping met platte kop voor een strakke pasvorm; 1/4 steel past op de meeste stiftslijpmachines en luchtgereedschap. 3/8 asgat past op Type 1 snij- en hakschijven. Lichtgewicht, duurzaam en het perfecte accessoire voor een stiftslijper.
Brand Weiler
Compatible Devices Die Grinder
Construction Type Cut-off Wheels
Country of Origin USA
Domestic Shipping Item can be shipped within U.S.
Grit Material Carbon Steel
International Shipping This item can be shipped to select countries outside of the U.S.
Is Discontinued By Manufacturer No
Item model number 56490
Manufacturer Weiler Corporation

3.7

13 Review
5 Star
78
4 Star
15
3 Star
4
2 Star
1
1 Star
2

Schrijf je beoordeling

Uw e-mail wordt niet gepubliceerd. Alle verplichte velden zijn gemarkeerd met*

Scritto da: Larry C.
Mandel 1/4 drive
Worked just fine, held the disk without any slipping, used it on several different tools, air drive and electric.
Scritto da: shawn
Works great in my MAC tool
This works great in my right angle air MAC Tool
Scritto da: Alvin Lenzen
Fast delivery
Wrks great fit perfectly
Scritto da: Duhuh
Works
Quick change out of grinder disks
Scritto da: Shooter McGavin
Four stars: not ground concentric.
I have two of these in two different grinders. They were both (and/or my grinders' collets) a bit out of whack.. One of my grinders normally runs rather smoothly. But with this mandrel chucked in it, it vibrated so bad that the cutoff discs frayed, the switch fell apart, the power leads broke off, and the case "ultrasonically" welded itself together in two spots. I had to tap it with a hammer to get the halves apart. After repairing the grinder, I chucked this mandrel back in and "turned" it true with a thick cutoff disc in another grinder while this mandrel was spinning at 25K rpm. You can easily see where the high/low spots are, due to the black finish. When there's no more black, it should be better. After making it concentric and removing a bit of unnecessary mass from the head, the vibrations went away. I also noticed the discs did not sit flat, so I took the screw out and faced the part that the bottom of the disc sits on, too, using the same method. Unfortunately, I had no way to face the bottom of the disc retaining screw in situ, but it was close enough to begin with that the discs now sit perfectly flat, and I did not need to fudge with it by, say, adding a cardboard washer or an O-ring between the disc and the retaining screw. The grinder is now super smooth and working fantastic with this mandrel. I think I'm gonna dedicate this grinder to cutoff discs, changing them out only with the mandrel screw. I'm afraid I might lose some smoothness/concentricity if I re-chuck the mandrel. These mandrels are made of carbon steel and the screw and threading are fine. They are solid. They are cheap enough that I would recommend them. Just have another grinder or Dremel tool handy, I think after going through this, I would true up any large mandrel in situ on any tool rotating at ridiculous RPMs, unless it were chrome plated and extremely well balanced to begin with. It's very fast and easy. Just keep both grinders oriented the same direction when you grind: tip to tip, butt to butt. If you try to "69" it, the cutting disc will just loosen, itself. This makes me wonder how reversible air grinders keep the cutting disc in place.
Scritto da: Opie
Works great with my die grinder
Works great with my die grinder
Scritto da: Jb
Perfect fit
Used this with circular saw blade (reviewed elsewhere) and cordless drill to trim concrete pavers. Sized as advertised.
Scritto da: Phils2888
Nice Cut Off Wheels
Work well in the shop
Scritto da: Daniel Parkes
Great for a die grinder
Using this in my die grinder. Unfortunately it didn’t fit my metric collet so I had to rub the shank down. Shipping took awhile to the uk. Didn’t realise it was in the US! Cuts great and does the job.
Scritto da: Brian
Top value for design & money
This is the very best design ! As the the top removable retaining stud goes through the blade into the stem ! While other versions only use a Phillips head short set screw ironic these are made by a blade company. These much superior by far !!
Scritto da: mb stelmach
The right centre hole size discs.
I've used them professionally for 40yrs+. A must in the aircraft industry.
Scritto da: tree
works
solid
Scritto da: Amazon Customer
Five Stars
Good product.Many thanks.

Gerelateerde producten

Ontdek ons ​​internationale netwerk

We verzenden naar 28 landen, meer dan 200.000 producten. Blijf op de hoogte, schrijf je in voor de nieuwsbrief.

Array